北京桑普高能科技有限公司

汽車座椅加熱系統 car seat heating system

一 綜合說明 General information

此款產品是我們多年研究的結晶,在控制方面采用微電腦控制,溫度任意調節,同時有30分鐘定時功能.組成更為簡單,只有兩部分,由插到點煙器上的控制器和連體熱片組成.發熱部分采用高科技發熱材料,升溫快. This product is the result of our effort on researching and developing through many years, the control system is controlled by the micro-computer, the temperature is adjusting freely, with 30minutes timing function. The product is made by only two sections, the controller which is plug in to the cigarette-plug plus pads, the heating element is adopted by hi-tech heating material, with the character of temperature raising rapidly.

二 是您冬季的好伴侶 your best companion in winter season

在每年寒冷的冬季,它升溫快,溫度任意調節,使您的腰酸腿疼有一定的緩解作用,對健康者-有一定的保健作用,可避免因寒風的入侵所引發的疼痛.in every cold winter, this product will reducing your painful of your waist and back through its rapidly temperature-raising and temperature-adjusting, it healthy to the people, to live away from the painful caused by cold wind.

三 安裝方法installation guide

1.將座椅的外座套取下,而后將發熱片的背面雙面膠撕開,再將發熱片粘貼到座和靠背上,再把座套套好.貼熱片時座和靠背粘貼時要成直角take out the outer cover of the seat, tear off the double-side sticky, stick the heating pad into the bottom and back from the seat, then re-cover the seat cover, it should be a 90degree angle while sticking the bottom and back

2.將加熱體的電極引出線從座和靠背的中縫處放于座椅下面.put the extend wire from electrode at the bottom of the seat where the position of the seat and back

3.將溫度控制器插到汽車點煙器的插座中.而后將控制器的插頭和發熱體的插座在座椅下方對接,這時座椅加溫系統就安裝好了.plug the temperature controller into the cigarette-plug, to connect the connector of controller with the connector of the heating pads under the seat, then the whole heating system is installed well.

四 使用方法users manual

1.將溫度控制器的開關從細的符號方向向粗符號方旋轉,這時電源燈和調溫?zé)敉瑫r(shí)亮,紅燈為升溫工作燈,綠燈為電源燈.turn the switch of the temperature controller from thin-sign to the thick-sign, the indicator of power and temperature-adjusting will be light-on at the same time, the red-indicator mean temperature raising indicator, the green-indicator means power indicator.

2.調溫開關上的溫度指示符號越粗表示溫度越高.即向粗符號方向旋轉到某一位置不動后,表示把溫度設定在此點上.the changes of thicker-sign of temperature indicator from temperature adjusting switch means raising the temperature steadily, the temperature will be set up wile you turn the switch to the thicker-sign and stay in a certain position.

3.如果在使用一段時間后發現溫度較高,這時可向細符號方向旋轉,將溫度設定低一些.if you feel the temperature is higher after you using it for a certain time, to reduce the set up temperature by turning the switch to the thinner-sign.

4.如果要關掉加熱系統,只需將調溫開關旋到溫度調節符號最小處后即可,這時控制器上的燈全部滅掉.if you want switch off the heating system, just turn the temperature adjusting switch into the minimize of the sign, the indicator from the controller will be off at this time.